1x Bluetooth4.0BLE USB Theta-Meter e-meter in a 50mm solo can

This is the first and the only Bluetooth4.0BLE (Bluetoth Smart) e-meter in the world. This device connects to a personal computer running Windows 8, 8.1 and 10, Apple Mac OSX, iPhone 5 and later, iPad3 and later, Android 4.4 and later using Bluetooth4.0 interface.

Also this e-meter can be connected to Windows from XP to Windows 10, Apple Mac OSX with a USB micro cable.
Warranty:2 years (except battery)
Features:

  • Battery charge lasts for approximately 50 hours
  • Time of charging approximately 4 to 6 hours
  • Bluetooth version: 4.0BLE (Bluetooth Smart) enabled
  • Bluetooth PIN code: 000000

To reset meter open meter with screwdriver and paper clip, remove battery from battery holder and put it back.

Supported operating systems:

This e-meter works with Bluetooth4.0BLE communication standard with Windows 8, 8.1 and 10, Android 4.4 and higher, Mac OSX, iOS 8.0 and higher if your device support this Bluetooth standard.

This device does not need any drivers installed, operating systems identify it as a standard Bluetooth4.0BLE device.

The Bluetooth Meter works with a personal computer using a USB cable and running Windows XP, Vista, 7, 8, 8.1, 10, Android 3.0-4.4 (not every Android device supports this type of connection) and Mac OSX.

Now we have good working software for Windows 8-10 and iOS. Other OSes not fully supported.

Setup of Bluetooth connection

To work with an iPhone or iPad there is no need to pair the devices just activate Bluetooth in the Settings.

Android 4.4 devices do not need any pairing. In Android 5.0 and higher activate Bluetooth in the Settings, choose Theta-Meter BT4.0 and enter code 000000.

For Windows 8, 8.1 and 10 press the Start button, choose Settings, then Devices and Bluetooth. Choose from the list Theta-Meter BT4.0 and press the Connect button, enter code 000000.

To provide reliable connection with smartphones disactivate LTE in Settings during sessions. LTE signal could block Bluetooth 4.0 connection.

For Mac OSX no pairing is required.

Short instruction

To activate the Bluetooth Theta-Meter press and hold for 2 seconds the power button at the one end of the device. If the e-Meter is charged and working the green LED start to blink.

To switch off e-meter press power button and keep it pressed for 2 seconds and the device will switch off.

To use the e-meter in duo can mode or to connect an exterior solo can or duo cans, press and quickly release the power button. The green LED starts to blink with 2 short blinks - device is now in duo cans mode. To return to the original condition press the power button for a short time and the device will start to blink once.

To charge the Theta-Meter BT4.0BLE and USB connect the Theta-Meter using the USB to Micro USB cable to the USB port of the notebook, computer or wall socket charger. If the device is discharged a red LED light will display. When the device is fully charged the red LED light no longer displays.

Theta-Meter Wi-Fi Access point

Theta-Meter Wi-Fi Access point is a Wi-Fi way to connect your Theta-Meter 2nd Generation to iPad, iPhone and iPod. Access point is not an e-meter, it transfer data from USB e-meter, connected to Access point to your iOS device.

Theta-Meter web browser program (for Chrome, Firefox, Opera, Vivaldi) is at 192.168.1.1/tmr/

More details you can read here.

Access point settings you can change at 192.168.1.1.

Operational systems

This Access point works with any operational system supporting Wi-Fi B and G.

Theta-Meter Wi-Fi Access point light

Theta-Meter Wi-Fi Access point light is a cheapest way to connect your Theta-Meter 2nd Generation to iPad, iPhone and iPod. Access point is not an e-meter, it transfer data from USB e-meter, connected to Access point to your iOS device.

Theta-Meter web browser program (for Chrome, Firefox, Opera, Vivaldi) is at 192.168.1.1/tmr/

More details you can read here.

Access point settings you can change at 192.168.1.1.

This Access point works with any operational system supporting Wi-Fi B and G.